Modules/EHCI - Header, no code yet

diff --git a/KernelLand/Modules/USB/EHCI/ehci.h b/KernelLand/Modules/USB/EHCI/ehci.h
new file mode 100644 (file)
index 0000000..431b039
--- /dev/null
+++ b/KernelLand/Modules/USB/EHCI/ehci.h
@@ -0,0 +1,156 @@
+/*
+ * Acess2 EHCI Driver
+ * - By John Hodge (thePowersGang)
+ *
+ * ehci.h
+ * - ECHI Header
+ */
+#ifndef _EHCI_H_
+#define _EHCI_H_
+
+struct sEHCI_CapRegs
+{
+       Uint8   CapLength;      // Byte offset of Operational registers
+       Uint8   _pad;
+       Uint16  HCIVersion;     // BCD Version
+       /**
+        * Structural Parameters
+        *
+        *  0: 3 = Number of ports on this controller
+        *  4    = Port Power Control
+        *  5: 6 = Reserved (ZERO)
+        *  7    = Port Routing Rules
+        *  8:11 = Number of ports per companion controller
+        * 12:15 = Number of companion controllers
+        * 16    = Port Indicators
+        * 17:19 = Reserved (ZERO)
+        * 20:23 = Debug Port Number
+        * 24:31 = Reserved (ZERO)
+        */
+       Uint32  HCSParams;
+       /*
+        * Capability Parameters
+        *
+        *  0    = 64-bit Addressing Capability
+        *  1    = Programmable Frame List Flag
+        *  2    = Asyncronous Schedule Park Capability
+        *  3    = Reserved (ZERO)
+        *  4: 7 = Isochronous Scheduling Threshold
+        *  8:15 = EHCI Extended Capabilitys Pointer (0 = None)
+        * 16:31 = Reserved (ZERO)
+        */
+       Uint32  HCCParams;
+       /*
+        * Companion Port Route Description
+        */
+       Uint64  HCSPPortRoute;
+};
+
+struct sEHCI_OpRegs
+{
+       /**
+        * USB Command Register
+        *
+        *  0    = Run/Stop (Stop, Run)
+        *  1    = Host Controller Reset
+        *  2: 3 = Frame List Size (1024 entries, 512, 256, Reserved)
+        *  4    = Periodic Schedule Enable
+        *  5    = Asynchronous Schedule Enable
+        *  6    = Interrupt on Async Advance Doorbell
+        *  7    = Light Host Controller Reset
+        *  8: 9 = Asynchronous Schedule Park Mode Count
+        * 10    = Reserved (ZERO)
+        * 11    = Asynchronous Schedule Park Mode Enable
+        * 12:15 = Reserved (ZERO)
+        * 16:23 = Interrupt Threshold Control
+        * 31:24 = Reserved (ZERO)
+        */
+       Uint32  USBCmd;
+       /**
+        * USB Status Register
+        *
+        *  0    = USB Interrupt
+        *  1    = USB Error Interrupt
+        *  2    = Port Change Detect
+        *  3    = Frame List Rollover
+        *  4    = Host System Error
+        *  5    = Interrupt on Async Advance
+        *  6:11 = Reserved (ZERO)
+        * 12    = HCHalted
+        * 13    = Reclamation
+        * 14    = Periodic Schedule Status
+        * 15    = Asynchronous Schedule Status
+        * 16:31 = Reserved ?(Zero)
+        */
+       Uint32  USBSts;
+       /**
+        * USB Interrupt Enable Register
+        *
+        *  0    = USB Interrupt Enable
+        *  1    = USB Error Interrupt Enable
+        *  2    = Port Change Interrupt Enable
+        *  3    = Frame List Rollover Enable
+        *  4    = Host System Error Enable
+        *  5    = Interrupt on Async Advance Enable
+        *  6:31 = Reserved (Zero)
+        */
+       Uint32  USBIntr;
+       /**
+        * Current microframe number (14 bits)
+        * 
+        * Bits 14:3 are used as n index into PeridocListBase
+        */
+       Uint32  FrIndex;
+       /**
+        * Control Data Structure Segment Register
+        *
+        * Most significant 32-bits of all addresses (only used if "64-bit addressing capability" is set)
+        */
+       Uint32  CtrlDSSegment;
+       /**
+        * Periodic Frame List Base Address Register
+        */
+       Uint32  PeridocListBase;
+       /**
+        * Current Asynchronous List Address Register
+        */
+       Uint32  AsyncListAddr;
+       // Padding
+       Uint32  _resvd[(0x40-0x1C)/4];
+       /**
+        * Configure Flag Register
+        *
+        * - When 0, all ports are routed to a USB1.1 controller
+        * 
+        *  0    = Configure Flag - Driver sets when controller is configured
+        *  1:31 = Reserved (ZERO)
+        */
+       Uint32  ConfigFlag;
+       /**
+        * Port Status and Control Register
+        * 
+        *  0    = Current Connect Status
+        *  1    = Connect Status Change
+        *  2    = Port Enable
+        *  3    = Port Enable Change
+        *  4    = Over-current Active
+        *  5    = Over-current change
+        *  6    = Force Port Resume
+        *  7    = Suspend
+        *  8    = Port Reset
+        *  9    = Reserved (ZERO)
+        * 10:11 = Line Status (Use to detect non USB2) [USB2, USB2, USB1.1, USB2]
+        * 12    = Port Power
+        * 13    = Port Owner (Set to 1 to give to companion controller)
+        * 14:15 = Port Indicator Control (Off, Amber, Green, Undef)
+        * 16:19 = Port Test Control
+        * 20    = Wake on Connect Enable
+        * 21    = Wake on Disconnect Enable
+        * 22    = Wake on Over-current Enable
+        * 23:31 = Reserved (ZERO)
+        */
+       Uint32  PortSC[15];
+};
+
+#endif
+